Acidic
Yes

Antibacterial
Yes

Certifications & Standards
ADA and CCD Compliant
<ul> <li>DFA Cosmetic</li> <li>Kosher</li> <li>Halal</li> <li>USDA</li> </ul>
<ul> <li>FDA Drug</li> <li>NSF</li> </ul>
ADA
EPA
FDA Drug
NSF

Cleaner Size
10.50" Width x 12" Length
11" Width x 12" Length
6" Width x 7" Length
7" Width x 8" Length

Dilution System
No
Yes

Directions/Instructions
Automatic Scrubbing Machines <ul> <li>1. Dust mop or sweep.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add four (4) oz. per gallon (30mL per liter) of this product to lukewarm water. Scrub floor with product. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely</li> </ul> Mop and Bucket Cleaning <ul> <li>1. Dust mop or sweep.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add two (2) oz. per gallon (15 mL per liter) of this product to lukewarm water. Mop floor clean with this product. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely.</li> </ul> Stone/Concrete Floor Daily cleaning (Automatic Scrubbing Machine): <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Add (1) oz. per gallon of this product to warm water. Scrub floor with product and Twister™ Intellipad®. Trail mop excessive wet areas behind scrubber. Do not rinse floor after cleaning.</li> <li>4. Let floor dry completely.</li> </ul> Stone/Concrete Floor Rejuvenation (Mop and Bucket method): <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Clean floor with a neutral floor cleaner according to label directions.</li> <li>4.Add thirteen (13) oz. per gallon (101 mL per liter) of this product to lukewarm water. Pick up soil and excess cleaner with a tightly wrung-out cleaning mop. Do not rinse floor after cleaning.</li> <li>5. Let air dry.</li> <li>6. For optimal gloss, burnish the floor with Twister™ Intellipad®.</li> </ul> Stone/Concrete Restoration: <ul> <li>1. Dust mop or sweep floor.</li> <li>2. Blockade areas to be cleaned. Floors will be very slippery until dry.</li> <li>3. Clean floor with a neutral floor cleaner according to label directions.</li> <li>4. Dilute this product with lukewarm water at a 1:1 dilution ratio. Apply up to 2 coats using a string mop or flat mop until desired shine is achieved. Be sure to evenly cover the entire floor. Do not rinse floor after cleaning.</li> <li>5. Let air dry.</li> <li>6. For optimal gloss, burnish the floor with Twister™ Intellipad®.</li> </ul> Best Results <ul> <li>Do not use on surfaces colder than 50°F/10°C</li> <li>To avoid contamination, do not return unused product to original container.</li> </ul> Note: Floors will be slippery when wet or contaminated with foreign materials. Promptly clean-up spills and foreign materials. Not intended for use in outdoor areas. Meets ASTM D-2047 requirements for slip resistance. Rubber Floors: For optimum appearance, alternate use of this product at standard dilution and ProfiTM/MC Degreaser once desired shine is achieved. On heavily worn rubber floors apply up to three coats of WiwaxTM/MC emulsion cleaner using the mop and bucket cleaning instructions with a 1:1 dilution ratio until desired shine is achieved. If high gloss is desired, apply instead, three coats of Carefree Floor Finish.
For General Use: <ul> <li>For use on hard, nonporous inanimate environmental surfaces such as floors, walls, glazed porcelain, glazed ceramic tile, plastic surfaces, shower stalls, bathtubs and cabinets</li> <li>To disinfect inanimate, hard nonporous surfaces, dilute according to label directions.</li> <li>Apply solution with a mop, cloth, sponge or hand-pump trigger sprayer so as to wet all surfaces thoroughly.</li> <li>Allow to remain wet for 10 minutes then remove excess liquid.</li> <li>For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution for each use.</li> </ul> For J-Fill® Use: <ul> <li>Insert cartridge into dispenser (see J-FILL® dispenser instructions for proper cartridge placement). Fill small bottle or bucket or use gun to apply a foam directly onto surfaces to be cleaned, scrubbing with a soft brush, pad or cloth. Do not allow foam to dry. Rinse surfaces thoroughly. NOTE: Some commercial strength cleaners are unsuitable for use on some surfaces. Test in an inconspicuous area prior to use.</li> </ul> For RTD® Use: <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul>
For Regular Use <ul> <li>Spray using full strokes 6-8" (15-20 cm) from surface</li> <li>Wait until stains disappear</li> <li>Wipe with sponge</li> <li>Rinse promptly</li> </ul> For Heavily Soiled Floors <ul> <li>Pour Crew® Tile & Grout Rejuvenator on the area to be cleaned</li> <li>Agitate with a stiff bristled brush and let stand for 15 minutes</li> <li>Repeat agitation and rinse with clean clear water with a mop and let dry</li> </ul> Crew Tile and Grout Rejuvenator easily removes stains as it whitens and brightens discolored grout. Powerful, ready-to-use combination of bleach and detergents power away tough soils and stains such as soap scum, mold, tea and coffee stains. Foaming trigger allows easy application onto vertical surfaces. Bleach-based cleaner with a chlorine scent can be used on most washable surfaces.
Recommended Dilutions: <ul> <li>Heavy Soil, Parts Wash and Immersion Cleaning: 1:24 - 1:32</li> <li>Medium Soil, General Cleaning, Floor Cleaning: 1:64 or 1:128</li> <li>Equipment, Machinery and Pressure Washing Cleaning: 1:128</li> <li>Light Soil, Auto Scrubbing: 1:256</li> </ul> Sprap-and-wipe Cleaning: Spray product onto surface to be cleaned. Wipe surface and rinse. In heavily soiled areas, allow the solution to penetrate for 2-4 minutes. When cleaning glass, ceramic tile, aluminum and painted surfaces, do not allow surface to dry. Rinse thoroughly. Floor Cleaning: Place slippery floor signs around the area. Apply solution onto the floor with a mop or autoscrubber. Pick up all excess solution from the floor. Rinse thoroughly to avoid corrosion Food Processing Areas: Before using this product in food processing establishments, food products and packaging materials must be removed from the area or carefully protected. After using this product, all surfaces in the area must be thoroughly rinsed with potable water. Avoid contamination of food during use or storage. NOTE: For painted surfaces, pretest a small inconspicuous area
Recommended Dilutions: <ul> <li>Heavy Soil, Parts Wash and Immersion Cleaning: 1:24 - 1:32</li> <li>Medium Soil, General Cleaning, Floor Cleaning: 1:64 or 1:128</li> <li>Equipment, Machinery and Pressure Washing Cleaning: 1:128</li> <li>Light Soil, Auto Scrubbing: 1:256</li> </ul> Sprap-and-wipe Cleaning: Spray product onto surface to be cleaned. Wipe surface and rinse. In heavily soiled areas, allow the solution to penetrate for 2-4 minutes. When cleaning glass, ceramic tile, aluminum and painted surfaces, do not allow surface to dry. Rinse thoroughly. Floor Cleaning: Place slippery floor signs around the area. Apply solution onto the floor with a mop or autoscrubber. Pick up all excess solution from the floor. Rinse thoroughly to avoid corrosion. Food Processing Areas: Before using this product in food processing establishments, food products and packaging materials must be removed from the area or carefully protected. After using this product, all surfaces in the area must be thoroughly rinsed with potable water. Avoid contamination of food during use or storage.
To clean bowls and urinals. <ul> <li>Remove water from bowl or urinal using swab.</li> <li>Apply to all porcelain surfaces.</li> <li>Cover all recesses and areas where stains can build up . . . under the rim, water outlets and drain pipe openings.</li> <li>Allow to stand for at least 60 seconds.</li> <li>For removal of heavier stains product can be left in bowl or urinal for up to 2 hours.</li> <li>Swab and flush rinse.</li> </ul>
Use Instructions <ul> <li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li> <li>Strip floors, using a Diversey stripper per the instructions on the stripper label</li> </ul> Coating <ul> <li>Apply 3 or more medium coats using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li> <li>Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li> </ul> Maintenance <ul> <li>Dust mop or sweep. Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li> <li>If desired, dry buff using medium to aggressive pad and 1000- 500 rpm equipment. Ultra-high speed burnish using a medium aggressiveness pad and 2000+ rpm equipment.</li> </ul> Recoating <ul> <li>Dust mop or sweep Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions</li> <li>Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before burnishing.</li> </ul> Removal <ul> <li>Remove using recommended Diversey brand stripper following label directions</li> </ul> Precautions <ul> <li>Do not dilute. Do not use on surfaces colder than 50°F (10°C) @ 15% RH. To avoid contamination, do not return unused finish to original container. Do not freeze.</li> </ul>
Use Instructions <ul> <li>Blockade areas to be stripped. Floors will become very slippery when stripper is applied. Exercise caution.</li> <li>Gloves, goggles and protective footwear is recommended when using this product</li> <li>Dilute or dispense using cold water</li> <li>Apply liberal amounts of stripper solution uniformly to floor with mop. Start at edges to provide more soak time. If splashing occurs, wipe off surfaces with a clean, damp rag.</li> <li>Let stripper solution soak 10-15 minutes. Mop agitate to loosen finish. Re-wet as necessary. Do not allow solution to dry on floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush. Pick up all solution with a clean mop, wet vac, or automatic scrubber. Mop up any 'tracks' left by wet vacs or scrubbers before they dry.</li> <li>Thoroughly rinse floor with clean water, using a mop and bucket. Let floor dry completely before applying a Diversey Green Seal®-Certified finish or other recommended Diversey brand floor finish or sealer.</li> </ul>
Use instructions <ul> <li>Thoroughly clean the sinks with a small amount of glassware cleaner prior to glass washing. Also, use clean brushes that are not worn.</li> <li>Set up sinks in four easy steps: 1. Fill first tank with hot or cold water almost to the top of the brushes. Add Beer Clean™ Mineral Solvent, if needed, based on local water-hardness conditions. 2. Add Beer Clean™ Glass Cleaner to the first sink, accurately measuring proper amount required or by sprinkling a pre-measured packet over the brushes. 3. Fill the second tank with clean, hot or cold, continuously flowing water. This tank is used to rinse off detergent from glassware used in the first sink. 4. Fill third sink with three gallons (11.5 liters) of hot or cold water. Add ¼ oz. Beer Clean™ Last Rinse Sanitizer. </li> <li>Wash glasses in the first sink, making sure that all glass edges come in contact with the brushes. If a three-brush manual system is used, clean glasses on the center brush. </li> <li>Rinse glassware in the second sink by placing the bottom of the glass in the water first, at an angle. If immersed top first, an air pocket can form, preventing complete rinsing. Withdraw the glass at an angle, bottom first ("heel in, heel out" technique). If you only have a two-tank system, do not include a rinse sink.</li> <li>Submerge glassware in sanitizing rinse solution (third sink) by using the "heel in, heel out" technique. Allow to remain immersed for at least 2 minutes. Follow national food service sanitation guidelines and local health codes for sanitizing. </li> <li>Air dry sanitized glassware upside down on a deeply corrugated drain board to allow maximum air flow. Do not dry glasses with towel, since it can leave lint on the glass and transfer germs and odors. Do not store glasses on a towel, rubber drain pad or any smooth surface.</li> </ul>
Use instructions <ul> <li>Use 1.0 mL to 3 mL per liter (0.128 to 0.384 oz./gal.) of water, depending on water hardness and soil conditions.</li> <li>Feed automatically into the dishmachine using a Diversey dispensing system.</li> <li>Contact your Diversey representative for correct set-up and operating conditions for your operation.</li> <li>Store at room temperature and avoid freezing.</li> <li>Do not use on aluminum or other soft metals.</li> </ul>
Use instructions Mop and Bucket Method <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Mop floors. No rinsing is necessary in non-food preparation areas.</li> </ul> Automatic Scrubber Method <ul> <li>Dust mop or sweep floor.</li> <li>Fill, dilute or dispense product according to label directions.</li> <li>Clean and scrub floors.</li> <li>Trail mop machine turns, edges and low spots in the floor to pick up cleaning solution left behind by machine.</li> </ul> Spray and Wipe Cleaning <ul> <li>Fill, dilute or dispense product according to label directions.</li> <li>Spray and wipe surfaces clean.</li> </ul> For RTD® Use: <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul>
Use instructions <ul> <li>Spray on hard surfaces to be cleaned.</li> <li>Allow power cleaner to penetrate and lift soils.</li> <li>Wipe with a clean cloth.</li> <li>Does not require a water rinse after use.</li> <li>Do not use on glass, aluminum or water-based paint.</li> <li>Suitable for use in areas where food or packaging will not come in contact with spray or surface during or after the use of this product.</li> </ul>
Use Instructions <ul> <li>Use appropriate personal protective equipment</li> </ul> Dilute product as follows: <ul> <li>Light Build-up of Floor Finishes: Dilute product between 1:8 (16 fl. oz. / gal.) and 1:10 (13 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Floor Finishes: Dilute product between 1:4 (32 fl. oz. / gal.) and 1:6 (24 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Concrete Sealers: Dilute product at 1:2 (64 fl. oz. / gal.) with cool water</li> <li>Blockade areas to be stripped. Floors will be very slippery when stripper is applied. Exercise caution.</li> <li>Apply liberal amounts of solution uniformly to floor with a mop. Start with the edges to give them more soak time. If splashing occurs, wipe off surfaces with a clean rag dampened with water.</li> <li>Let stripper solution soak for 10-15 minutes. Mop agitate to loosen finish or sealer. Re-wet as necessary, do not allow stripper to dry on the floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush</li> <li>Pick-up all of the solution with a clean mop, wet vac or automatic scrubber</li> <li>Mop up any "tracks" left by wet vacs or automatic scrubbers before they dry. Thoroughly rinse floor with clean water, using a mop and bucket.</li> <li>Let floor dry completely before applying recommended Diversey brand floor sealer or finish</li> </ul> Important: <ul> <li>Do not use on wood, linoleum, rubber, marble, painted surfaces, on surface colored and acid dyed concrete floors as this product may harm these surfaces. Test for softening or color bleeding on asphalt floors before using.</li> </ul>
Use instructions <ul> <li>Use BreakDownTM/MC Odor Eliminator on all organic odors and stains.</li> <li>General Deodorizing: Dilute 1:32 with water (4 ounces per gallon/ 31 mL per liter).</li> <li>Washroom: Dilute 1:20 with water (6 ounces per gallon/50 mL per liter). Apply around urinals, toilets, on floors and in trash receptacles.</li> <li>Plumbing Pipes (drains, sinks, disposals, toilets): Pour 4 ounces (120 mL) of BreakDownTM/MC Odor Eliminator into drain pipes 2 times per week when drain flow is lowest.</li> <li>Carpet Odors and Stains for Spotting: Test carpet for colorfastness. Use BreakDownTM/MC Odor Eliminator full strength. Follow good spotting procedures. Re-apply BreakDownTM/MC Odor Eliminator. Let stand 20 minutes.</li> <li>General Carpet Cleaning: Dilute 1:64 with diluted cleaning solution (2 ounces per gallon/15.6 mL per liter).</li> </ul>
Use instructions <ul> <li>Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical.</li> </ul> Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> For Use as a Non-Acid Toilet Bowl and Urinal Disinfectant/Cleaner <ul> <li>Empty toilet bowl or urinal and apply use-solution to exposed surfaces and under the rim with a sprayer.</li> <li>Brush or swab thoroughly, allow to stand for contact time indicated on the label and flush.</li> </ul> To Control Mold and Mildew <ul> <li>Follow disinfection instructions.</li> <li>Repeat treatment every seven days, or more often if new growth appears.</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:256 dilution - Bactericidal, Virucidal, and Fungicidal, in 3 minutes. Kills HIV-1 and Influenza Type A in 1 minute. Some organisms require a 10 minute contact time and/or other dilutions. Please see product label or reference sheet for complete information.</li> <li>1:128 dilution - Kills Norovirus in 5 minutes.</li> </ul>
For Prespray Cleaning <ul> <li>Thoroughly vacuum carpet and pre treat spots.</li> <li>Dilute 10 oz. Heavy Duty Prespray with 1 gallon hot water (1 L with 12 L) in pump-up sprayer or fill directly from J-Fill® dispenser.</li> <li>Spray carpet completely, paying particular attention to traffic lanes and spots.</li> <li>Agitate with a carpet rake, extractor brush, shampoo brush or bonnet.</li> <li>Allow 5-10 minutes for Heavy Duty Prespray to completely loosen soils.</li> <li>Thoroughly extract carpet with Extraction Rinse according to use directions. Use Liquid Defoamer in recovery tank if required.</li> </ul> For Bonnet Cleaning <ul> <li>Dilute at 1:32 or 4 oz./gal. (35 mL per L) with warm water.</li> <li>Apply light mist onto carpet bonnet.</li> <li>Bonnet buff carpet with your pad. Flip pad when soiled. When both sides are soiled, rinse or launder.</li> <li>e This solution can also be used for spot treatment. Treat spot, agitate and rinse thoroughly.</li> </ul>
Specs & Application Instructions: <ul> <li>Formulated to work in HE machines but can be used in all types of laundry machines</li> <li>Commercial and industrial laundry machines, as well as standard laundry machines</li> </ul>
Specs & Application Instructions: <ul> <li>Use where odors are a problem</li> <li>Can be used in hospitals, nursing homes, schools and colleges, offices, public areas and restrooms</li> <li>Use on hard, non-porous restroom surfaces: glazed ceramic tile, glazed porcelain, chrome, stainless steel and plastic surfaces associated with floors, walls, fixtures, toilets, urinals, sinks, shower rooms and locker rooms.</li> </ul>
Use instructionsShake can before using. Remove cap and hold container 6 to 8 inches from surface being sprayed. Push button, spray lightly and wipe immediately with a clean dry cloth. DO NOT allow spray to dry before wiping. Use wherever you want long lasting beauty.TO POLISH chair rungs, table legs or other small areas, spray directly on cloth and wipes the surface. Use in same manner to REMOVE STAINS, SMUDGES and FINGERPRINT
Use instructionsTo sanitize pre-cleaned and potable water-rinsed, non-porous, food contact surfaces, prepare a 200-400 ppm active quaternary solution by adding 1 ounce of sanitizer to 4 gallons of water.To Sanitize Stationary Kitchen and Food Processing Equipment:<ul><li> This product can be used to clean and sanitize hard, non-porous surfaces of equipment such as deli slicers, beverage equipment, ice machines and dispensers.</li><li> Clean with this product according to the label directions.</li><li> To sanitize, apply a use-solution of 0.25 - 0.5 fl.oz. per gallon of water (200 - 400 ppm active) or equivalent dilution by spraying or swabbing until thoroughly wet.</li><li> Allow surfaces to remain wet for at least 60 seconds.</li><li> Drain thoroughly before reuse and allow to air dry</li></ul> For Use as a Cleaner:Apply Use Solution 1 fl. oz. - 4 fl. oz. of product per 5 gallons of water to hard, non-porous surfaces. Wipe surfaces and let air dry.For Sanitization:When used as a food contact sanitizer at a 1:512 dilution (1.0 fl. oz. of product per 4 gallons of water), (0.25 fl. oz. per 1 gallon of water) in the presence of 500 ppm hard water, this product reduces the following bacteria by 99.999% with a 1 minute contact time on pre-cleaned, hard non-porous inanimate surfaces.For Non-Food Contact Sanitization:When used as a non-food contact sanitizer at a 1:512 dilution, 1.0 fl. oz. of product per 4 gallons of water (0.25 fl. oz. per 1 gallon of water), this product reduces the following bacteria by 99.9% with a 3 minute contact time on pre-cleaned, hard non-porous inanimate surfaces.To Sanitize Hard, Non-Porous Food Contact Surfaces and Equipment:<ul><li> Prior to sanitization, remove gross particulate matter with a warm water flush, then wash equipment with detergent or cleaning solution and follow with a potable water rinse.</li><li> Prepare the sanitizing use solution by adding 0.25 - 0.5 fl. oz. per gallon of water (200 - 400 ppm active quat).</li><li> Apply sanitizing solution by immersion, coarse spray, mop, wipe, flood techniques or circulation techniques as appropriate to the equipment or surface to be treated. Allow a contact time of at least 1 minute.</li><li> Allow surfaces to drain thoroughly and air dry before resuming operation. Do not rinse.</li></ul> DISINFECTION DIRECTIONS:Thoroughly clean with this product according to label directions. Spray diluted J-512TM/MCSanitizer onto surface until wet. After wetting surface, allow surface to air dry or immerse for at least 10 minutes and then let airdry. DO NOT RINSE. DO NOT WIPE.For Disinfection of Food Contact Surfaces:After disinfection of food contact surfaces is complete, rinse surfaces and please follow food contact sanitizer directions found on product label. Diluted Product for Disinfection:@ 1:160
Use instructions<ul><li> Prior to application, thoroughly clean all surfaces to be treated to remove gross filth or heavy soil.</li></ul> Disinfectant<ul><li> Hold can upright and spray from a distance of 6 to 8 inches until area for treatment is thoroughly moistened. Allow to remain wet for 10 minutes. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li></ul> Control of Mold and Mildew<ul><li> Spray surface until thoroughly moistened. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li><li> Repeat application in 7 days.</li></ul> Control of Fungus<ul><li> Spray surface until thoroughly moistened.</li><li> Allow surfaces to remain wet for 10 minutes.</li><li> Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li></ul>
Important: Do not use with hot water, bleach, disinfectants or chemical drain openers as these will reduce product performanceOdor Control<ul><li> (Restrooms, Dumpsters, Kennels, Health Care, Restaurants, Schools, Prisons): DO NOT SPRAY INTO AIR OR USE AS AN AIR FRESHENER</li><li> REMOVE SOLID WASTE BEFORE APPLYING. Dilute 1:1 to 1:10 (128 oz. to 12 oz. / gal. [3.78 L to 355 mL / 3.78 L] warm water).</li><li> Apply with trigger sprayer, sponge, mop or cloth. This product must contact surface to be effective.</li></ul>Drain Lines/Down Pipes/Plumbing<ul><li> To prevent clogging of restroom, kitchen/mop sinks; floor/laundry drains; toilets/urinals; dishwashers/garbage disposals: Use two to four times a week at 4 oz. (118 mL) for every 2 inch (5 cm) inside diameter of pipe</li><li> For best results, treat at the end of the day or when flow is lowes</li></ul>
This product can be used in multiple areas such as operating rooms, long-term care facilities, medical facilities, animal treatment facilities, cruise ships, hotels (motels), public buildings, public restrooms, recreational facilities, retail businesses and schools (colleges and universities)
<ul> <li>A highly effective cleaner designed to remove soils and oils without dulling or altering the appearance of your floor</li> <li>Designed for use on most floor types</li> <li>Part of a comprehensive floor care offering for cleaning, maintaining, stripping and finishing floors</li> </ul>
<ul> <li>Add the product at ½ oz. per gallon of water (1:256).</li> <li>Pre-clean heavily soiled areas.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use solution to hard, non-porous environmental surfaces. To disinfect, all surfaces must remain wet for 10 minutes.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> Note: Rinsing is not necessary unless floors are to be coated with finish or restorer. All food contact surfaces such as appliances and kitchen countertops must be rinsed with potable water. Do not use on glassware, utensils or dishes For Use as a Cleaner and Deodorizer <ul> <li>Apply use solution to hard, non-porous surfaces. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul> For Use as a Non-Acid Bowl Cleaner/Disinfectant in Toilet Bowls and Urinals from Use-Dilution Empty toilet bowls by forcing water through the trap. Apply use solution to exposed surfaces in toilet bowls and urinals. Swab entire surface area especially under rim. Allow entire surface to remain wet for 10 minutes. Flush toilet or urinal and rinse swab applicator thoroughly. For Use to Clean and Disinfect Shower Rooms, Locker Rooms and Other Large, Open Areas with Floor Drains <ul> <li>Apply use solution to floors, walls and ceilings. All surfaces must remain wet for 10 minutes. Scrub and rinse surfaces thoroughly and let air dry</li> </ul> To Kill Mold, Mildew and Fungi (in 5% soil load) <ul> <li>Apply use solution to hard, non-porous environmental surfaces and allow surfaces to remain wet for 10 minutes. Wipe and let air dry</li> </ul> To Control Mold and Mildew <ul> <li>Apply use solution to pre-cleaned hard, non-porous environmental surfaces and allow to air dry. Repeat weekly or when growth reappears</li> </ul>
<ul> <li>Available in dilution control for ease in use, safety and cost control</li> <li>Can also be used for carpet spotting and extraction cleaning</li> <li>Use in autoscrubbers, mop and bucket and spray-and-wipe applications</li> </ul>
<ul> <li>Can be used on glass and many washable surfaces such as chrome, stainless steel, sinks, bathroom fixtures and laminate surfaces such as countertops.</li> <li>Do not use on copper or brass as repeated use may discolor these surfaces.</li> </ul>
<ul> <li>Clean and disinfect high-touch surfaces in just ONE Minute</li> <li>Non-irritating to eyes and skin</li> </ul>
<ul> <li>Dispense Crew® Bathroom Cleaner and Scale Remover using cold water at 1:18 into spray bottle.</li> <li>Apply ready-to-use solution on a damp cloth or spray directly on surface to be cleaned and let dwell for several seconds</li> <li>Rub surface with cloth or non-abrasive cleaning pad.</li> <li>Rinse surface with clear, cold water.</li> <li>Polish with a dry soft cloth.</li> <li>Do not use on wood or marble.</li> <li>Test in an inconspicuous area since certain surfaces may be unsuitable for commercial strength cleaners</li> <li>Always stand on a non-slip surfaces when in shower or tub.</li> </ul>
<ul> <li>Ensure the EasyWipe Disposable Wiping System is compatible with the desired type of chemical solution. Read Safety Data Sheet (SDS) and test the chemical solution with the wipes to determine compatibility.</li> <li>Understand any hazards related to the chemical solution and its use by consulting its SDS. Follow all applicable safety advice and use appropriate protective equipment. For questions about safe chemical solution use, contact your supervisor or site occupational safety professional.</li> <li>Fill out the label with all information about the added chemical solution or apply the appropriate aftermarket label to the bucket. Note: This label does not replace the manufacturer or supplier's SDS.</li> <li>Slowly pour chemical solution over the top of the roll. Use approximately one half gal. (74 oz. / 1.9 L) of chemical solution in the 1 gal. (3.78 L) bucket. More or less liquid may be required to obtain the desired saturation level.</li> <li>Thread the end of the wiper from the CENTER of the roll through the lid opening. Snap the lid on.</li> </ul>
<ul> <li>For use as daily and general cleaner.</li> <li>Versatile formula that performs in a variety of application methods such as an autoscrubber, spray and wipe and mop and bucket</li> </ul>
<ul> <li>Hard surface cleaning and disinfection</li> <li>Designed for disinfecting medical hard, nonporous inanimate surfaces including: glass, glazed porcelain and stainless steel. Not recommended for use on: aluminum, brass, chipped enamel, clear plastic, copper, finished floors, natural marble, painted surfaces, and silver.</li> </ul>
<ul> <li>Pre-clean heavily soiled areas.</li> <li>Apply product by coarse trigger spray to hard, non-porous inanimate surfaces.</li> <li>All surfaces must remain visibly wet for 1 minute. Use 5-minute contact time for TB and a 3 minute contact time for fungi.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul> Note: Rinsing is not necessary unless floors are to be coated with finish or restorer. All food contact surfaces must be rinsed with potable water. Do not use on glassware, utensils, or dishes. Prior to first use on a particular surface, it is recommended to test in a small, discreet area if there is concern of incompatibility, or contact a Diversey representative. To Spot Sanitize Soft Surfaces <ul> <li>Remove gross filth prior to sanitization.</li> <li>Hold bottle upright 6" - 8" from surface.</li> <li>Spray until fabric is wet. DO NOT SATURATE. Allow surface to remain wet for 30 seconds.</li> <li>Gently blot with a clean, damp, color safe cloth and/or let air dry. For difficult odors or heavy fabrics, repeat application.</li> <li></li> </ul>
<ul> <li>Pre-clean heavily soiled areas.</li> <li>Wipe hard, non-porous environmental surfaces with towelette.</li> <li>Allow surface to remain wet for 1 minute. (For certain listed viruses, allow to remain wet for 30 seconds).</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul>
<ul> <li>Spray & wipe cleaner for hard surfaces</li> <li>Use to remove marker and paint</li> <li>Cleaner/Degreaser for shops and kitchens NSF C-1</li> </ul>
<ul> <li>Spray surfaces and let solution remain on surface for a minimum of 5 minutes</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:16 dilution - Virucidal, Bactericidal, and Fungicidal, including antibiotic resistant bacteria, in 5 minutes</li> <li>1:128 dilution - Non-food contact sanitizer in 3 minutes or general purpose cleaning</li> <li>1:256 dilution - Floor and general purpose cleaner</li> </ul> Note: Rinsing is not necessary unless floors are coated with finish or restorer.All food contact surfaces must be rinsed with potable water. Do not use on glassware, utensils or dishes. Prior to first use on a particular surface, it is recommended to test in a small, discreet area if there is concern of incompatibility, or contact a Diversey representative. Not recommended for floors at dilution 1:16. Refer to product label for complete use instructions.
<ul> <li>Use as a spray-and-wipe application</li> <li>Use on any water-washable hard surface</li> </ul>
<ul> <li>Use on hard, nonporous surfaces including vinyl, painted surfaces, plastic, glazed ceramic, glazed porcelain, chrome, laminated surfaces and bakes enamel surfaces</li> <li>Effective in health care, educational, lodging and food service environments</li> </ul>
<ul><li> For use as a powerful rinse aid</li><li> Safe to use on all colorfast carpets</li></ul>
<ul><li> Responds beautifully to conventional, high-speed or UHS equipment and maintenance procedures</li><li> May require a sealer on highly polished stone, glazed clay tile, and some rubber floors</li><li> Not intended for use on cork, wood, or bamboo flooring unless specified by the manufacturer</li></ul>
<ul><li> Use as a daily floor cleaner on most floor types</li><li> Can also be used as a high performance general purpose cleaner</li></ul>
<ul><li> Use for glass and mirror cleaning</li><li> Can be used on multi-surfaces</li></ul>
<ul><li> Use for glass and mirror cleaning</li><li> Can be used on multi-surfaces</li></ul>
If being used on a carpet for the first time test for colorfastness on an inconspicuous area. Remove gross soil. Extract using Extraction Rinse. Dilute product 1 to 4 oz. per gallon (30 to 120 mL/3.78 L). Saturate the spot/stain and surrounding area. Agitate. Place towel moistened with product over treated area for 24 hours. Remove towel and repeat treatment as necessary. Extract with Extraction Rinse. Allow carpet to dry. Use also as a drain cleaner and odor counteractant cleaner in restrooms; or bonnet buff using the dilutions outlined above.directions.
Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical. Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted.</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul>

Dispensing Quantity
0.01 fl oz to 0.03 fl oz Per Stroke

Form
Lotion

Fragrance Classification
Alcohol
Fresh
Lemon Tea Splash

Freshener/Sanitizer Type
Aerosol
Liquid

Freshener/Sanitizer Volume
16 fl oz (0.5 quart)
84.5 fl oz (2.6 quart)

Moisturizing
Yes

Non-Acidic
Yes

Operating Mode
Automatic/Manual
Manual

Pest Control
Wasp

Pesticide Type
Spray

Pesticide Volume
15 fl oz

Product Material
ABS Plastic
Plastic
Steel

Skin Type
Dry

Sprayer Type
Trigger

Volume Capacity
1.37 quart
18 fl oz (532 mL)
20.30 fl oz
44 fl oz (1300 mL)

Popular tags

Luxe

Diversey, Inc

View as Grid List

Sort by

Display per page

Beer Clean Glass Cleaner

DVO990221

Concentrate Powder - 100 / Carton - White

$83.97 $36.60

Diversey Stride Citrus Neutral Cleaner

DVO93063390

Concentrate Liquid - 153.6 fl oz (4.8 quart) - Citrus Scent - 1 Each - Orange

$194.62 $85.19

Diversey Crew Tile and Grout Rejuvenator

DVO101104392CT

Ready-To-Use Spray - 32 fl oz (1 quart) - Chlorine Scent - 1 Each - Light Yellow

$87.36 $83.50

Diversey Crew Bathroom Cleaner/Scale Remover

DVO93145310

Ready-To-Use Liquid - 50.7 fl oz (1.6 quart) - Surfactant ScentSpray - 2 / Carton - Purple

$120.77 $81.24

Diversey Care RTD Water Hose & Quick Connect Kit

DVO3191746

Green, White, Gold - 1 Each

$52.08 $31.95

Diversey Glass/Multi-Purpose Cleaner

DVO100975197

Concentrate - 84.5 fl oz (2.6 quart) - 1 Each - Non Ammoniated, Streak-free, Quick Drying, Non-smearing, Fragrance-free, Dilutable, Odorless, Kosher - Blue

$99.63